Long Pole Module (70cm) for MDM04 MDM05 MDM06 MDM07 Multi Monitor Arm Bracket
|Price:||£14.98 FREE UK delivery.|
- Enter your model number above to make sure this fits.
- Pole Module for MDM0X desktop monitor mount series: MDM03 MDM04 MDM05 MDM06
- Long pole module, the length is 70 cm long; the diameter of the pole is 3 cm (1,2")
- The perfect solution if you want to upgrade your desk monitor mount form MDM0X series.
- made of strong metal with podwer coating
- elegant silver finish, matching the color of your stand
Frequently Bought Together
Customers Who Bought This Item Also Bought
Size: Pole Long (70 cm)
70cm Pole Module for MDM0X series: MDM03 MDM04 MDM05 MDM06.
The perfect solution if you want to upgrade your desk monitor mount from MDM0X series.
What do customers buy after viewing this item?
Top Customer Reviews
1 - Not what I thought it was: This long arm is NOT a replacement for the short arm part (the monitor bracket part will NOT fit directly into this arm).
2 - Not really fitting: The part with the thread is not quite long enough for a correct installation with all components (1x large washer, 1x small washer and 1x spring washer). At least the large washer need to be removed, which in turn may cause damage to the lackered surface between the two arms during final installation (hence only 3 stars, it can be used somewhat, but I think it is not ideal).
3 - Visual impact (if it matters): If used with MDM05 (Dual monitor setup), you will need two (2) of these arms, in order to keep both monitors aligned at the same height. The difference in height is about 38mm if only one arm is used.
On one pole is 2 monitors using 3 arms each to give enough width to fit them side by side. (The kit came with 4 arms, so I needed to buy 2 of these long arms in order to have enough length for these screens)
On the other pole is 2 arms. The monitors are 2 Dell 27 inchers that are very heavy and one is a light BenQ. The full kit holds them perfectly and I can rotate them them about. You just need to make sure that you use the spanner to tighten each arm very tight to prevent sag, once this is done it's all fine.
I didn't expect this kit at this price to be able to hold such large and heavy screens so kudos to Allcam!
You will need a cross-head screwdriver and an adjustable spanner or an appropriate spanner for fitting the tray, they supply the spanner and Allan key for the the arms and the swivel but nothing for tray.
It is a bit fiddly getting the cables into the ducts, I found the easiest way was remove the ducts, fit the cables in to the ducts and then fix the ducts in place. This requires that the hight of the assembly is adjusted last so that you have room to get a short screwdriver under the lowest arm of the assembly.
Be aware that the lip at the front of the tray obscures access to front edge of the laptop which is a problem if you have audio ports or switches on the front edge of your laptop. You may need to be 'remodel' the tray to suit your laptop or live with the limitation.
You may find that you need to extend the assembly with an additional MDM Long Arm Module if your desk is deep, it just depends on how near you need the screen to your sitting position, which can be an issue if you use glasses for computer work or reading.
In addition the heads of the screws holding the tray to the swivel head on the arm sit proud and can scratch the bottom of your laptop. You can use some of these 33 Assorted Anti-Skid Pads felt stuck to tray to raise up the laptop sufficiently to prevent it rubbing on the screw heads and it also increases the air gap under the laptop for ventilation.
The main problem is that the support arm that came with the laptop tray did not come with the required number of nuts and washers for assembly. It was missing one M8 nyloc nut, one 25 mm washer, one 8 mm spring washer and one 8 mm plain washer, all of which are used to fix the shaft of the star shaped end piece onto the last arm. Fortunately I had all of these parts to hand but it might be annoying for others to have to try and source them.
Only other comment I have is that the whole thing is only as stable as the desk you are fitting it to!
I only have two issues with it.
First, there is no way to adjust how the arm joints are configured so even in it's lowest position your laptop sits pretty high off the desk.
Second, the screw for mounting the tray to the arm are not flush with the surface of the tray and there is nothing to guard against these scratching the bottom of your laptop. This is unfortunate but can be remedied with a small sheet of felt, ART & CRAFT FELT FABRIC PADS SHEETS SQUARES 8 COLOURS PER PACK A4 SIZE(20X30 CM) SPECIAL OFFER. FREE 4 PACK WITH EVERY 8 PACK PURCHASED or pads 33 Assorted Anti-Skid Pads felt There are foam pads for the bottom lip though and these are quite thick. It's a pity they didn't supply something similar for the back.
Most Recent Customer Reviews
Excellent fully cast and machined extension arm. Would fully recommend. Quick arrival time. Good customer phone assistance.Published 3 months ago by John E. [Watchdog].
Very sturdy, holds the laptop well. Did have a couple of lumps of metal sticking up from the base I thought might scratch my laptop so chiseled them off with a screw driver. Read morePublished 4 months ago by Maemo_Fan
This is huge!, and very strong, I bought it to hang in front and above my graphic drawing board so I dont have to move the tablet every time I need to access the keyboard and it... Read morePublished 5 months ago by Ron Wylie
I have normal sized 24" monitors x 3. Bit annoyed that I needed to purchase this add-on to accommodate them. That being said its robust-ish.Published 6 months ago by Amazon Customer
Using this extender put too much strain on the original arms causing my screens to fall sideways onto the floor. Was not happy about this but no harm done in the end. Read morePublished 7 months ago by L Johnson
This is a must have - I can't imagine the monitor stand would meet ergonomic requirements for monitor to reach eye level without the 70cm pole. Read morePublished 9 months ago by London Reviewer